Can You Cut LVP With a Miter Saw? (How To Do It)

A miter saw is a saw that positions a mounted blade onto a board to create precise crosscuts and miters in a workpiece. Miter saws are most commonly used for cutting wood trim and molding, but they may also be used to cut metal, masonry, and plastics if the right blade is used for the job.

A miter saw is convenient since all you need to do is make a little mark and the saw will take care of the rest. This tool is suitable for cutting flawless 90-degree cuts or any other angle up to 50 degrees for most saws.

LVP may be cut using a miter saw, but it must be oriented perfectly in front of the blade. Before the cutting process begins, the saw blade must never contact the material.

In most cases, if the saw is correctly set up and the canvas is clamped down exactly where it needs to be, this cuts nicely and without issues.

How Do You Cut the Vinyl Plank With a Miter Saw?

Vinyl cuts differently than wood or even metal since it is a synthetic substance. With any type of plastic flooring, having the correct blade may assist ensure a clean-cut, but it’s also crucial to move gently to avoid burnt boards or chipped edges.

Cutting Vinyl Flooring to Length

Cutting boards to length is the most typical cut you’ll need to make when laying vinyl flooring. Mark the board for the cut using the tape measure. To avoid pencil markings and the risk of damage, always utilize the reverse of the vinyl plank flooring. This also protects the wear layer from miter or table saw the damage.

Mark the cut line across the back of the board with the speed square. Whatever saw you use, remember to go slow, take your time, and stick to the line.

Cutting Vinyl Flooring to Width

Things may rapidly become tricky when cutting a piece of vinyl plank to width. You won’t be able to make this cut using a compound miter saw or a handsaw; instead, you’ll need to use a circular saw or a table saw. Mark the board on the back as you would with any other cut, but pay close attention to the edge that goes against the wall is the cut side. Measure and mark each end of the board for the cut using the tape measure. 

Cutting Vinyl Flooring around Pipes and Corners

You’ll have to make a few unusual cuts if you’re putting vinyl flooring in a room with plumbing or a radius corner. You may do this in a variety of ways, depending on the position of the pipes and the distance between them, and any barriers. Some flooring installers “notch” a cut where the pipe should be, and while it works, it isn’t very clean.

Cutting Peel and Stick Vinyl Plank Flooring

Simply measure, mark, and cut the piece with a utility knife to cut peel, and stick vinyl plank flooring or tiles. Klein flooring cutters are great for thick luxury vinyl or EVP flooring, but they’re too big for thin planks or flooring. Any type of cut can be made with a razor knife and a straight edge.

Can I Use a Table Saw to Cut Vinyl Flooring?

When cutting vinyl planks, a table saw may be quite beneficial, especially when executing a rip cut. A rip cut is when you cut the boards along their length. This would usually be done where the vinyl planks’ long edges contact the wall.

You can cut this material using a table saw in a variety of ways, not just rip cuts. You may also use the table saw to crosscut your vinyl boards. When you need to shorten the length of the plank, you’ll need to use a crosscut.

Can You Use a Circular Saw to Cut Vinyl Plank Flooring?

Circular saws can and are frequently used to cut vinyl plank flooring, and if you have one in your garage or woodshop, it may be used to cut this material effectively.

The base plate will probably be too large for a normal vinyl plank. When dealing with thinner materials, circular saws can sometimes cause kickback. Metal-cutting circular saw blades are not compatible with wood-cutting circular saws, which is an issue for some vinyl planks.

Wrap Up

With the correct equipment, practically any homeowner can cut vinyl plank flooring. However, with hundreds of manufacturers producing tiles and planks, finding the appropriate sort of vinyl flooring can be difficult.

If you’re installing vinyl flooring in a room with plumbing or a radius corner, you’ll have to make a few odd cuts. Simply measure, mark, and cut the piece with a utility knife to cut peel, and stick vinyl plank flooring or tiles. When cutting vinyl planks, a table saw may be helpful, especially when executing a rip cut. Metal-cutting circular saw blades are not compatible with thin planks or flooring.