Can You Cut Roots With a Chainsaw (The Easiest Way)

It’s one thing to cut down a tree; it’s quite another to get rid of the stump. Yes, there are many options, but which one is the most effective? You may either use chemicals or a stump grinder to get rid of the stump. However, we believe that using a chainsaw is the most straightforward and efficient method.

For cutting purposes, you already have a chainsaw. This time, you may also clean out the stump with the same power tool. We’ll show you how to use a chainsaw to remove a tree stump.

cut roots with a chainsaw

Chainsaws are strong equipment that dirt won’t damage or lose its chain. Keep in mind that some timber might be left beneath the earth. Large roots can also be taken out by cutting vertically into the ground and then pulling them out with a shovel or pickaxe.

How Do You Cut a Tree Root With a Chainsaw?

A chainsaw is versatile equipment that may be used for a wide range of tasks. Once you’ve been properly educated, you’ll be able to utilize this talent to remove trees from your yard or other wooded areas. There are several rules to observe when cutting tree roots with a chainsaw.

  1. Put on your PPE (Personal Protective Equipment) and head outside.
  2. Cut the stump as abject to the ground as is practically possible;
  3. Remove the Stump’s Dirt using a Shovel;
  4. Remove the roots;
  5. Stump the Stump; Stump the Stump; Stump the Stump; Stump the
  6. Getting Rid of the Stump;

What Is the Easiest Way to Cut Tree Roots?

You may admire your yard’s tree but despise the roots that are ripping up your walkway or blocking your plumbing. So, what are your alternatives for dealing with them? Is it possible to get rid of these roots without hurting your tree?

Step 1: To dampen and soften the soil surrounding the tree, water it well. Allow the water to soak into the soil for a few minutes, then wait until the soil is wet but not waterlogged.

Step 2: Overturn the top layer of dirt with a hand trowel to loosen it. Feel for the roots and be careful not to stab them with the trowel blade too many times.

Step 3: Remove the dirt by hand and place it in a wheelbarrow or on a tarp for now. Scoop away soil from the sides and beneath the roots, only using the trowel to break up compacted soil as necessary.

Step 4: Trim the ends of any roots that require trimming. Making clean cuts through the roots using a root saw is a good idea. Trim roots from the trunk no closer than three times the diameter of the trunk. Trim roots just to the point where the diameter reaches a fist’s size or greater. Remove no more than one-third of the total roots on one side and no more than one-quarter on the other.

Step 5: Dig a trench in front of the roots that have been trimmed. Install a robust root barrier composed of plastic, metal, or concrete in the ditch. Use a root barrier that is at least 12 inches high and 10 feet long for more powerful roots.

Step 6: Cover the roots and the root barrier with the previously dug soil. Compost and peat should be added to unhealthy soil. Fertilizer should be used after at least 6 weeks. After compacting the dirt and raising the ground level, properly irrigate the area.

What Should You Not Cut With a Chainsaw?

Chainsaws are a very efficient instrument, but they may also be quite deadly if handled wrong. Before you start using the chainsaw, make sure you have all of the necessary safety precautions in place.

When operating a chainsaw, avoid the following mistakes:

  1. Don’t cut into the dirt; 
  2. Don’t cut with improper blade tension; 
  3. Don’t use used motor oil in the chain lube reservoir;
  4. Don’t refuel your chainsaw when it’s hot; 
  5. Don’t put the brake on while putting the pedal to the metal; 
  6. Don’t use a dull blade; don’t leave old gas in the tank over the winter;
  7. Instead of 2-cycle oil, do not add car motor oil to the gas;
  8. If your chainsaw’s air filter is dirty, don’t use it;
  9. If a chainsaw is resting against any part of your body, do not start it;
  10. Don’t stand in front of the saw;
  11. A saw should never be left running unattended;
  12. Carry chainsaws only when they are not in use;
  13. Make sure you don’t come into contact with the muffler. There is a risk of severe skin burns; 
  14. Do not cut alone.

Is It Safe to Use a Chainsaw to Cut Roots?

No, it is not safe to use a chainsaw to cut roots. Chainsaws are designed for cutting wood, not roots. If you try to cut roots with a chainsaw, you can damage the chainsaw and potentially injure yourself.

What Type of Chainsaw is Best for Cutting Roots

The best type of chainsaw for cutting roots is a gas-powered chainsaw with a long bar length (18-20 inches). This type of chainsaw allows for a deeper cut and more control when cutting roots. Look for a chainsaw with a low-kickback bar and chain, an adjustable oiler, and an anti-vibration system for improved comfort and control.

Final Thoughts

Finally, tree stump removal is a rather simple job if done correctly. Make use of diagonal and different cutting ways, and avoid clogging your chainsaw with too much dirt and debris. Remove the stump after cutting and pulling out the roots.

Featured image credit: youtube.com

Read more:

Rate this post

About This Writer

david rowan author

Hello, I am David Rowan. I am a professional contractor with 10 years of experience in home building, different tools used, construction, home remodeling, and other home improvement work. I have already built many custom homes and continued to do several woodworking projects along with how to deal with all categories of tools.

Hello, I am David Rowan. I am a professional contractor with 10 years of experience in home building, different tools used, construction, home remodeling, and other home improvement work. I have already built many custom homes and continued to do several woodworking projects along with how to deal with all categories of tools.

Leave a Comment