7 Bandsaw Resawing Tips From a Professional Woodworker

A band saw is an ideal contraption to cut a significantly thicker saw. It moreover comes to make various kinds of irregular cuts. The band saw is very popular for resawing work. It is not so hard through the bandsaw. But many woodworkers, especially those who are new to this wood industry and do not know the tips and techniques, are not getting a good results on resawing timber. 

Some tips make your job better and easier. Some professional woodworkers share their tips for bandsaw resawing; among them, 7 tips are discussed in this blog. All of them worked in the wood industry for a long time. Their real-life experiences help you a lot. 

bandsaw resawing tips

Tips That Turn You into an Expert

Knowing the technique of a job makes it easier. There are some tips and techniques for bandsaw resawing that make you an expert. Some of it is given below.

1. Picking the Right Blade for Resaw 

The blade is a very important part of the band saw. Many thick lumbers are cut when resawing is done. The work will not be good if the right blade is not selected. The blade edge goes through the wood. At that time, the cutting-edge tooth shaves off a tremendous measure of sawdust, which goes into the canal or space between two teeth of the bandsaw blade.

When the canal is full of sawdust at that moment, the blade can not cut the wood properly, which makes resawing much more of a problem.    

For resawing, you should use blades that have enough space between the teeth of the blade. So while picking a cutting edge for resawing thick timber, ensure that it has at least 3 teeth for each inch to have the option to cut the stock productively.  Even if lots of wooden sticks or sawdust are stuck in such a blade, there is no problem in your resaw work. Read more: Things to Consider When Choosing the Best Tile Saw.

2. Square the Bandsaw Sharp Edge and the Board

Ensuring the sharp bandsaw edge is opposite to the table is particularly significant when you’re re-sawing a wide board. For the best outcomes, raise the guidepost as far as possible and utilize a square with an arm that coordinates the saw’s resaw limit.

Change the table, so no holes show up between the sharp edge and the arm. Next, ensure the board has a square corner. That way, it will ride flush against both the tall fence and the table during the cut.

3. Weight the Sharp Edge for Ideal Execution

Acceptable forefront pressure helps keep stacking zeroed in whether or not your control isn’t awesome, and it diminishes the edge’s penchant to waver under push. It’s definitely not hard to set a satisfactory proportion of strain. Present a Wood Slicer edge on your saw with equal assistants and push heading open up and backed off both above and underneath the table, so they don’t contact the edge. 

With the saw unplugged, wrench on some strain, and a while later mindfully give the edge a sharp sideways punch with your pointer somewhere close to the upper and lower wheels. The sharp edge will divert a short partition.  A while later seems to arrive at a halting point;  if you push fundamentally harder, it will bend farther. Anyway, there’s a particular point where it quits evading with no issue. Also, read the user guide: Find the Best Sanders for Refinishing Furniture.

As of now, adding pressure until this sideways improvement is just 1/4″ to 5/16″ on saws with 6″ significance of cut, or around 3/8″ to 1/2″ on saws with 12″ significance. Unexpectedly, don’t look at the saw’s characteristic strain check until you’re done; there’s no convincing motivation to confuse yourself with emotional numbers. After you’ve gotten the hang of tensioning by feel, check the quantifier and use it’s scrutinizing as a game plan control while tensioning the edge later on. 

As of now, track your bleeding edge on the upper wheel, so the most significant bit of the neck of the edge is at the centerline of the tire. This technique gives you the best result when you resaw.   

4. Adjust Bandsaw Blade for Perfect Resawing

It is one of the important tips for making a resaw from the bandsaw.  For this, near the wheel covers without bringing the level collaborators and pushing the heading up near the blade.

 Then turn on the bandsaw and, at this time, ensure the blade is following respectably at max power. By any chance, if it is not working, then change the setting with settings as essential until it’s after remarkable.

 At this time, if the blade does not work properly, it will be vibrating. To stop this vibration, extend or diminish the weight fairly. Do this until the edge runs directly in a viable manner from wheel to wheel of your bandsaw. 

5. Thickness Planer for Fine Finish

Many times when you go to resaw wood on the bandsaw, you don’t get a fine or smooth surface. Then these tips will help you. If the function used an authentic feed rate to deal with the stock through the saw, all the pieces will come out with fine finishing and smooth surface. Read more: Which Palm Sanders are Best for Woodworking?

If you want this, then work through a thickness planer. This tip makes your job easier. There is no need to smooth the new resawing wood. 

6. Clean Blade

Timber of different shapes and sizes are cut with this bandsaw. As a result, different pieces of wood are stuck with this machine.  Material crusted around the teeth will constantly cause it to be as difficult for them to slice as in the event that they were deadly dull, and it can influence the cutting edge’s lead point, as well. Read more: Choosing the Perfect Circular Saws for Woodworking Project.

If you don’t clean the bandsaw properly, there will be problems when cutting wood. It is tough to resaw with an unclean bandsaw. So clean your resawing bandsaw blade properly after using it, and it also keeps acting like a new saw.

7. Safety Issue

Always remember safety facts when you work with the bandsaw. The bandsaw might be the most un-perilous resawing apparatus in the shop. However, consistently recall that anything that transforms hardwood into sawdust can do a lot more terrible damage to you.

Resawing on the bandsaw is not so easy. If you want to work with safety, try to use a push block. It will help you to push the timber on the saw without touching your finger. Keep your finger away from the blade. Little safety can change your fate.

Does the Moisture Content of Wood Affect Bandsaw Resawing?

The moisture content of wood greatly impacts bandsaw resawing. Proper wood drying techniques are essential to achieve clean and accurate cuts. Excessive moisture can cause warping, uneven cuts, and decreased blade performance. It’s crucial to use well-dried wood to optimize the resawing process.

Conclusion

If you know about a bandsaw setup for resawing, this will reduce your workload by half. Through all these tips in this blog, you know more about resawing. Hope that all this should help kick you off effectively.  Standard practice will get you in and assist you with getting better at resawing wood on your bandsaw.

You might also like:

Rate this post

About This Writer

Author Eric Devin

Hi, I am Eric Devin and I am a professional interior architect. Since childhood, I've always enjoyed DIY projects! And, I have loved to solve simple household problems using essential tools and equipment. I have also acquired a lot of information about basic household tools settings by working with contractors.

Hi, I am Eric Devin and I am a professional interior architect. Since childhood, I've always enjoyed DIY projects! And, I have loved to solve simple household problems using essential tools and equipment. I have also acquired a lot of information about basic household tools settings by working with contractors.

Leave a Comment